Wavelength division demultiplexing by photonic crystal waveguides with asymmetric corrugated surfaces

<正>We propose a new type of wavelength division demultiplexer composed of a photonic crystal waveguide with asymmetric corrugated exit surface.The focus displacement for different symmetric corrugated surfaces is relative to the intensity of the excited surface mode.By systematically investigating the effects of the parameters of the corrugated surface on the focus shift,we demonstrate an on-axis focus by a photonic crystal waveguide with an asymmetric corrugated exit surface at a specific wavelength.The precise equivalences of surface modes at each side of the exit surface are broken.Thus,for the light source with other wavelengths,the emerging beams are off-axis focused at different directions,similar to the function of a wavelength division demultiplexer.     

难加工材料切削机理研究的新进展

航空发动机重要零件如机匣、压气机风扇叶片等广泛采用钛、镍基合金等先进结构材料.钛、镍基合金材料切削加工性较差,主要表现在材料热硬度和热强度很高,所需切削力很大,工件、刀具容易产生较大变形;材料热扩散率低;刀具切削深度线位置缺口现象严重,以及形成锯齿状切屑等几个方面.深入研究此类难加工材料的切削机理,对于实现薄壁件高效精密数控加工技术至关重要.本文重点介绍了关于高硬度金属材料锯齿状切屑的形成机制;非连续切屑形成过程的有限元数值模拟关键技术,包括自适应网格细化、切屑与工件之间的分离准则,以及用以描述单元网格中裂纹形核与扩展的断裂准则和算法;切削区域高温、高应变率条件下材料屈服流动行为的准确描述,系统考虑应变、应变率和温度三者之间的相互影响作用;切削温度场、工件表层残余应力场的分布规律,以期消除残余扭曲变形对航空工业中普遍使用的薄壁结构件加工精度的显著影响.      

变磁阻传感器的计算机设计及精度仿真

本文介绍了变磁阻式高精度角位移传感器的基本原理及设计特点;着重讨论了用电子计算机进行该类传感器绕组、磁场的联合设计计算以及输出特性和精度的仿真方法;并对影响变磁阻传感器精度的因素以及减小误差的方法进行分析讨论。变磁阻传感器精度的理论计算和设计数据与实验结果相符合。     

X-band AlGaN/GaN HEMTs with high microwave power performance

An X-band AlGaN/GaN high-electron-mobility transistor (HEMT) on SiC substrate with high microwave power performances has been achieved. Its small-signal characteristics with a gate-length of 0.4 μm showed a unity current gain cut-off frequency (fT) of 22 GHz and a maximum oscillation frequency (fmax) of 65 GHz. The GaN HEMT device with a gate width of 1 mm exhibited a continuous-wave saturated output power of 10.2 W and a linear gain of 14.8 dB at 8 GHz, and successfully achieved the power-added efficiency ...     

Study on the saturation characteristics of high-speed uni-traveling-carrier photodiodes based on field screening analysis

A back-illuminated mesa-structure InGaAs/InP charge-compensated uni-traveling-carrier(UTC) photodiode(PD) is fabricated,and its saturation characteristics are investigated.The responsivity of the 40-μmdiameter PD is as high as 0.83 A/W,and the direct current(DC) saturation current is up to 275 mA.The 1-dB compression point at the 3-dB cutoff frequency of 9 GHz is measured to be 100 mA,corresponding to an output radio frequency(RF) power of up to 20.1 dBm.According to the calculated electric field distributions in the depleted region under both DC and alternating current(AC) conditions,the saturation of the UTC-PD is caused by complete field screening at high optical injection levels.     

半导体激光器的线宽压窄及频率连续调谐

我们利用共焦F—P腔光学弱反馈技术，实现了单模GaAlAs半导体激光器线宽压窄、频率锁定及连续调谐。其线宽从自由运转时的10MHz被压窄到45kHz，并可将频率锁定于共焦F—P腔。实验证明，在弱反馈情况下，激光器的频率连续调谐范围与共焦FP腔的光强反馈量近似成正比，实现了在铷原子D2线附近1．2GHz的频率连续调谐，     

1．55μm InGaAsP／InP应变量子阱激光器的LP－MOCVD生长

本文首次报导了生长温度为５５０℃，以三甲基镓（ＴＭＧａ）和三甲基铟（ＴＭＩｎ）为Ⅲ族源，用低压金属有机物气相沉积（ＬＦＭＯＣＶＤ〕技术，高质量１．６２ｕｍ和１．３ｕｍＩｎＧａＡｓＰ及Ｉｎ０．５７Ｇａ０．４３Ａｓ０．９８Ｐ０．０４／Ｉｎ０．７３Ｇａ０．２７Ａｓ０．６Ｐ０．４量子阶结构的生长，并给出了１．５５ｕｍＧａＡｓＰ／ＩｎＰ分别限制应变量子阱结构激光器的生长条件，激光器于室温下脉冲激射，其阈值电流密度为２．４ｋＡ／ｃｍ２。     

镜面起伏对1.55μm Si基MEMS光滤波器的影响

用传输矩阵方法,在简化的光学模型基础上,分别讨论了分布式Bragg反射镜DBR(Distributed Bragg Reflector)的生长精度及镜面起伏对1.55 μm Si基MEMS(Micro-Electro-Mechanical-System)可调谐光滤波器透射谱的影响.计算表明:DBR生长误差仅使主透射峰位置发生变化,而镜面起伏是导致主透射峰性能劣化的主要原因,它使得FWHM增大,透射峰强度下降.理论计算结果能较好地解释实验现像.在此基础上,进一步讨论了引起镜面起伏的多种原因,并提出了可能的解决方法.     

Synthesis of layered double hydroxides/graphene oxide nanocomposite as a novel high-temperature CO2 adsorbent

In this contribution, a novel high-temperature CO2 adsorbent consisting of Mg-Al layered double hydroxide(LDH) and graphene oxide(GO)nanosheets was prepared and evaluated. The nanocomposite-type adsorbent was synthesized based on the electrostatically driven self-assembly between positively charged Mg-Al LDH single sheet and negatively charged GO monolayer. The characteristics of this novel adsorbent were investigated using XRD, FE-SEM, HRTEM, FT-IR, BET and TGA. The results showed that both the CO2 adsorption capacity and the multicycle stability of LDH were increased with the addition of GO owing to the enhanced particle dispersion and stabilization. In particular, the absolute CO2 capture capacity of LDH was increased by more than twice by adding 6.54 wt% GO as support. GO appeared to be especially effective for supporting LDH sheets. Moreover, the CO2 capture capacity of the adsorbent could be further increased by doping with 15 wt%K2CO3. This work demonstrated a new approach for the preparation of LDH-based hybrid-type adsorbents for CO2 capture.     

高温热处理气氛对低氟MOD法制备YBCO超导薄膜的影响研究

金属有机物沉积法(MOD)制备YBa2Cu3O7-x(YBCO)涂层导体是最具有商业前景的方法之一.本文使用环烷酸铜代替三氟乙酸铜,降低了前驱液中大约50%的氟含量.然后在带有缓冲层(Y2O3/YSZ/CeO2)的Ni-5at.%W基带上采用MOD法制备了YBCO薄膜并系统研究了高温热处理过程中气体流速和氧分压对YBC...